How to pull and read ECU trouble codes - Mazda Forums : MazdaWorld.org Mazda Owners Forum

MazdaWorld.org is the premier Mazda Forum on the internet. Registered Users do not see the above ads.
Reply
 
LinkBack Thread Tools
  #1 (permalink)  
Old 06-01-2005, 07:49 PM
The_Saint's Avatar
Platinum Member
 
Join Date: Feb 2005
Location: Uzbekistan
Posts: 5,402
Send a message via AIM to The_Saint Send a message via Yahoo to The_Saint
Default

Mazda 929
Year: 1992 to 1995


Jump GRD and TEN in the diagnosis connector under the hood with a wire With the ignition switch on and count the flashs of the check engine light.








Trouble Shooting the error:


01 Ignition Pulse

No Data

02 Crank Angle Sensor, Ne Signal




03 Crank Angle Sensor, G Signal



04 Distributor, Ne 1 Signal



05 Knock Sensor



06 Speedometer Sensor



07 Knock Sensor, RH Side

See Error code 5

08 Air Flow Meter



__________________

well last night I was going back to uni, I stopped at the drivethru and this damned homeless guy stumbles over to the eunie and the drivethru window, and starts pestering the guy for food, and is grabbing as he passes me the food. he has this hugeass bottle of beer, and then as i'm rolling up my window the ******* keeps knocking at it asking for a favour... then heres where the **** hits the fan, the ******* spills his beer all over the eunie's DS fender and on the hood.........!!!!!!!!

i so wanted to get out and kick his ass but mommy was there... (she takes the eunie back home after I drive myself to school ... so he staggers out in front of the eunie, and I turn on my brights and lean on the horn... he acts all stupid and then stumbles off to the side and falls down; so but anyway, 5 minutes later when I get to school and I'm madly wiping the paint and apologising profusely to the eunie, and she's like "its just beer " GRRRRRRRRRRRRRRRRRRRRRRRRRRR!!!!!!!!
[Source]
-------------------------------------------------------
http://img330.imageshack.us/img330/220/duel9xm.gif Violence is the last refuge of the incompetent.
<span style="color:white">-------------------------------------------------------
Reply With Quote
Sponsored Links
Advertisement
 
  #2 (permalink)  
Old 04-06-2006, 11:22 PM
The_Saint's Avatar
Platinum Member
 
Join Date: Feb 2005
Location: Uzbekistan
Posts: 5,402
Send a message via AIM to The_Saint Send a message via Yahoo to The_Saint
Default

09 Water Thermo Sensor




10 Intake Air Thermosensor in Air Flow meter



11Intake Air Thermo Sensor Dynamic Chamber



12 Throttle Sensor (Full Range)



13 Pressure Sensor

No Data

14 Atmospheric Pressure Sensor

If code 14 is present, replace ECU.

15 O2S



16 EGR Switch



17 Feedback System





18 Throttle Sensor, Narrow Range

No Data

20 Metering Oil Pump Position Sensor

No Data

23 Fuel Thermo Sensor

See Error code 15

25 Solenoid Valve, Pressure Regulator Control

No Data

26 Metering Oil Pump, Stepping Motor



27 Metering Oil Pump

No Data

28 EGR Vaccum Solenoid Valve



29 EGR Vent Solenoid Valve



30 Cold Start Injector Relay




31 Solenoid Valve, Relief

No Data

32 Solenoid Valve, Switch

No Data

33 Port Air Solenoid Valve

No Data

34 Solenoid Valve, Idle Speed Control



36 & 37 Right/Left Oxygen Sensor Heater Relay



38 Solenoid Valve, Accelerated Warm Up System

No Data

39 Solenoid Valve, Relief 2

No Data

40 Solenoid Valve, Purge Control

No Data

41 Variable Resistance Induction System



42 Solenoid Valve, Turbo Pre Control

No Data

43 Solenoid Valve, Wastegate Control

No Data

44Solenoid Valve, Turbo Control

No Data

45 Solenoid Valve, Charge Control

No Data

46 Solenoid Valve, Charge Relief

No Data

50 Solenoid Valve, Double Throttle Control

No Data

51 Fuel Pump Relay

No Data

54 Air Pump Relay

No Data

65 A/C Imput Signal



71 Injector, Front Secondary

No Data

73Injector, Rear Secondary

No Data

76 Slip Lockup Off Signal

No Data

Torque Reduced Signal

No Data


Clearing Codes:

After you have repaired or replace any parts that you believe was the cause of the ECU error code, you will need to clear the code from the ECU.

1) Disconnect negative battery cable. Depress brake pedal for
at least 5 seconds. Reconnect battery cable.
2) Ground test connector with jumper wire. Turn ignition on,
but do not start engine for 6 seconds. Operate engine at 2000 RPM for
2 minutes. Verify no codes are displayed.
__________________

well last night I was going back to uni, I stopped at the drivethru and this damned homeless guy stumbles over to the eunie and the drivethru window, and starts pestering the guy for food, and is grabbing as he passes me the food. he has this hugeass bottle of beer, and then as i'm rolling up my window the ******* keeps knocking at it asking for a favour... then heres where the **** hits the fan, the ******* spills his beer all over the eunie's DS fender and on the hood.........!!!!!!!!

i so wanted to get out and kick his ass but mommy was there... (she takes the eunie back home after I drive myself to school ... so he staggers out in front of the eunie, and I turn on my brights and lean on the horn... he acts all stupid and then stumbles off to the side and falls down; so but anyway, 5 minutes later when I get to school and I'm madly wiping the paint and apologising profusely to the eunie, and she's like "its just beer " GRRRRRRRRRRRRRRRRRRRRRRRRRRR!!!!!!!!
[Source]
-------------------------------------------------------
http://img330.imageshack.us/img330/220/duel9xm.gif Violence is the last refuge of the incompetent.
<span style="color:white">-------------------------------------------------------
Reply With Quote
  #3 (permalink)  
Old 08-24-2010, 01:31 AM
Mazda Newbie
 
Join Date: Aug 2010
Posts: 6
Default how to do for protege?

anybody know how to do this ECU code reading for 95 protege?
Reply With Quote
Sponsored Links
Advertisement
 
Reply


Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -4. The time now is 01:09 AM.



Powered by vBulletin® Copyright ©2000 - 2012, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO 3.6.0
Garage Plus vBulletin Plugins by Drive Thru Online, Inc.